This commit makes several changes:
1. It adds modules for the dictionary builder and errors headers.
2. It captures all of the macros that are used to configure these headers.
When the headers are imported as modules and one of these macros is defined
the compiler issues a warning that it needs to be defined on the CLI.
3. It promotes the modulemap file into the root of the lib directory.
Experimentation shows that clang's `-fimplicit-module-maps` will find the
modulemap when placed here, but not when it's put in a subdirectory.
When re-using a compression state, across multiple successive compressions,
the state should minimize the amount of allocation and initialization required.
This mostly matters in situations where initialization is an overwhelming task
compared to compression itself.
This can happen when the amount to compress is small,
while the compression state was given the impression that it would be much larger,
aka, streaming mode without providing a srcSize hint.
This lean-initialization optimization was broken in 980f3bbf83 .
This commit fixes it, making this scenario once again on par with v1.4.9.
Note that this does not completely fix#2966,
since another heavy initialization, specific to row mode,
is also happening (and was not present in v1.4.9).
This will be fixed in a separate commit.
Apparently, even when the assembly file is empty (because
`ZSTD_ENABLE_ASM_X86_64_BMI2` is false), it still is marked as possibly
needing an executable stack and so the whole library is marked as such. This
commit applies a simple patch for this problem by moving the noexecstack
indication outside the macro guard.
This commit builds on #2857.
This commit addresses #2963.
the new contracts seems to make more sense :
updateRep() updates an array of repeat offsets _in place_,
while newRep() generates a new structure with the updated repeat-offset array.
Most callers are actually expecting the in-place variant,
and a limited sub-section, in `zstd_opt.c` mainly, prefer `newRep()`.
to act on values stored / expressed in the sumtype numeric representation required by `storedSeq()`.
This makes it possible to abstract away this representation by using the macros to extract these values.
First user : ZSTD_updateRep() .
this meant to abstract the sumtype representation required
to transfert `offcode` to `ZSTD_storeSeq()`.
Unfortunately, the sumtype numeric representation is currently a leaky abstraction
that has permeated many other parts of the code,
especially within `zstd_lazy.c` and also within `zstd_opt.c` and `zstd_compress.c`.
While this PR makes a good job a transfering a large nb of call sites
to using the new macros, there are still a few sites where this transformation is more complex,
or where the numeric representation itself it used "as is".
One of the problematics area is the decision to use the numeric format of the sumtype
within the match finders of `zstd_lazy`.
This commit doesn't change the behavior, it only introduces and employes the macros,
but eventually the resulting code remains identical.
At target, if the numeric representation of the sumtype can be completely abstracted
and no other part of the code depends on it,
it will be possible to move it towards something slightly more efficient.
`CFLAGS=-O0 make`
will now use `-O0` instead of enforcing `-O3`
which used to be the behavior before introduction of `libzstd.mk`.
This should result in faster tests,
since a few tests depend on this capability for faster roundtrips.
since this is effectively what is stored in this field (== matchLength - MINMATCH).
This makes it clearer what needs to be done when reading from / writing to this field.
the variable has only very limited usage,
being only used once at the beginning of the block for prefetching only,
hence the error had no impact on compression ratio.
This saves some 1.7Kb in rodata section (x86_64, zstd tool),
while assembler code stays the same except
the type of a few load/extend instructions.
Should not have negative performance implications.
mostly for maintenance convenience.
Performance wise, there is very little change,
slightly faster for slog 3 & 4,
neutral or very slightly negative for slot 5 & 6.
I couldn't find a good way to spread `ip0` and `ip1` apart when we accelerate
due to incompressible inputs. (The methods I tried slowed things down quite a
bit.)
Since we aren't splaying ip0 and ip1 apart (which would be like `0_1_2_3_`, as
opposed to the `01__23__` we were actually doing), it's a big ambitious to
increment `step` by 2. Instead, let's increment it by 1, which has the benefit
sliiightly improving compression. Speed remains pretty much unchanged.
The position updates are rewritten from `ip[N] = ip[N-1] + step` to be
`ip[N] = ip[N-2] + step`. This lets us only deal with the asymmetric spacing
of gaps at setup and then we only have to keep a single `step` variable.
This seems to work quite well on GCC and Clang!
This replicates the behavior of @terrelln's `ZSTD_fast` implementation. That
is, it always looks at adjacent pairs of positions, and only applies the
acceleration every other position. This produces a more fine-grained
acceleration.
no idea why visual + clang-cl + appveyor don't like them,
I've not been able to reproduce the issue locally,
but these static assert are very unlikely to deliver a useful signal,
I can't imagine a situation where they will be wrong,
and if they are, then a ton of other things will be broken way before reaching that point.
W. Felix Handte